INOKATSU MTW M4 SOPMOD REVIEW (PREVIEW)

[erichaitran]

any info on the "redwolf version"? any specific problems? mine is still in customs. They are holding everything i have ordered so far, and im buggin out.

Wait, from what i see in your picture, there is a new mag in the box. did it come with a mag or did you order one with the ino?

[DOC]

From the description of the actual "Enhanced" version at Redwolf:
http://www.redwolfairsoft.com/redwolf/airsoft/ProductDetail?prodID=25949

...Includes:
4x Rail Covers (Black).
2x Spare Magazine Gas Ejection Port.
Spare Hop-up rubber and O-Ring.

- This gun DOES NOT come with a magazine. The magazine in the photo is used for illustration purposes only.
You will need to buy the following mag for this gun:

-Western Arms 50rds Magazine for WA M4A1 CQB/R or Western Arms 50rds S-Type Magazine for WA M4A1

Please purchase a WA M4 Standard [WA436] or S-Type Magazine [WA446].
Please remember to upgrade your O-rings with the G&P Magazine Top-Gas O-Ring Set for WA M4A1 [WP80].
Also note that the Inokatsu CO2 magazines have not yet been released.

Since RW recommends the use of the G&P mag O-ring set, does anyone have tested them already?

DOC

[erichaitran]

hey, you never know, they couldve added a mag for those who waited a month and a half since preorder.

[Stinger]

Mine didn't come with a mag I preorder at Redwolf from day one.

Need help, I encounter my first problem with my Inokatsu, I'm using a redgas everything is going well no missed fire or anything some the bolt with not complete the cycle but the that's because of the magazine low pressure but last night when I switch it from semi to auto and after full the charging handle the bolt goes forawrd but the bolt carrier stay half way, I have to disassemble the receiver extesion to get the bolt group.

This is what I found a part of the o-ring is caught in between the bolt carrier and the bolt.
How can I disassemble the bolt group?

[IBICO]

This is what I found a part of the o-ring is caught in between the bolt carrier and the bolt.
How can I disassemble the bolt group?

There is a U clip back where the end of your nozzle is inside the bolt carrier. You should see a knob with a U clip on it. take that off and you could take out the complete nozzle

[Stinger]

There is a U clip back where the end of your nozzle is inside the bolt carrier. You should see a knob with a U clip on it. take that off and you could take out the complete nozzle

Thank you IBICO and Merry Christmas to all, I went to my friend house yesterday (he is a EAG Guru) and put our heads together and tried to fix and figure out what causes the problem. And to disassemble the bolt group there are three steps.

1. On the front right side of the bolt carrier when you are looking at the top there is a hex type micro screw unscrew the grub screw using a hex key, that serve as lock for unthreaded screw like that hold the bolt.

2. Just lift the head of that screw lock with the tip of a box knife and it will pop out.

3. Lift the u-clip at the rear of the bolt.




We found out that the bolt need to be clean and lube, good thing the gun comes with a spare o-ring got that also fixed, but my only regret is not knowing the size of it so I can buy some more.

Those who own a Inokatsu M4 can you please kindly post the size of the o-ring for further reference.

System of Measurement = Inch

[erichaitran]

so i got my inokatsu today, and there is no end to the dissapointment that came when i took a closer look after work.

here are a few problems i have noticed so far.

- front sight pins impossible to remove
- my magpul grips fit like they are on the original WA M4 body
- magazines dont fit in the magwell....
- anodizing seems a bit cheep

i plan on getting the the upper and lower blasted, sanding the magwell down, and swapping all the internals into my prime kit.

i was stoked when it came in, but not im just a bit angry for forking $870, and waiting for 2 months for a steel trigger assembly and bolt, because thats about all that works right. Enhanced version my ass.


anyone else with this issue?

[MCXL]

I had too put the mag in and remove it about 10-15 times before it would drop free, adonising is simply a bit thick.

As for the grips I cant attest too that, as my MIAD STILL hasn't come, but im not worried.

Front pins come out fine on mine, you doing it from the correct side?

[DOC]

On my INO MBK, the MIAD grip fits well but not perfect (little gap in the rear but hardly noticeable).
Magwell is Ok, mag drops free but the fit of upper and lower together is a joke...

DOC

[erichaitran]

the only rear grip piece that fits is the B1 small. also, the front F4 piece that has the built in trigger guard doesnt line up well like it does on the prime.

also, im kinda damaging my mags when im trying to fix my magwell.

got the front sight pin out, took alot of force to push out. it was a bit bent.